Corro-Dur 257 Cold Cure

 

Features and Highlights:

 

  • Novolac System
  • Flexibilized
  • Solvent Free System
  • 100% Volume Solids
  • Moisture Tolerant System
  • Non-Hazardous Material
  • Excellent Chemical Resistance
  • Physical Resistance
  • Hydrocarbon Resistance

 

Uses:

 

  • Coating ONLINE onto sweating / cold pipe
  • Tank coating
  • Underwater application
  • Chemical Tank Coating
  • Anti-corrosive Coating
  • Maintenance Coating
  • Secondary Containment Protection
  • Wastewater Protection
  • Riser repair
  • Splashzone coating
  • Rebuilding of wall loss

 

CORRO-DUR 257 COLD CURE is based on a unique blend of liquid epoxy polymer and aliphatic polyamine curing agents with an inert plasticizer, which is able to displace water from wet surfaces in order to make a permanent bond. The formulation is solvent-free to ensure safety and maximum technical performance. Kevlar™ fibers are incorporated for reinforcement and viscosity management to achieve high application rates. The resin system is tailored towards applications under predominantly cold and wet wintry conditions in temperatures down to 4.4°C (40°F).

 

CORRO-DUR 257 COLD CURE provides permanent protection under the most aggressive marine and industrial conditions. The formula is uniquely field-friendly and uses advanced low toxicity ingredients.

 

CORRO-DUR 257 COLD CURE may be immersed in fresh or salt water immediately after application. It will cure to a hard film within about 14 hours and is suitable for traffic after this time. Allow at least three (3) days curing at 77°F (25°C) before subjecting to severe service.

 

ANTICORROSIVE COATING: Marine and Industrial “heavy duty” maintenance applications, wet or dry and specifically designed for cold sweating condition.

 

WASTEWATER: Reinforcing, smoothing a protection worn concrete damaged by exposure to chemical or municipal waste streams.

 

HYDRO GENERATION : Easy application to wet concrete for smoothing, sealing and freeze-thaw spalling prevention. Ideal for dam face and penstock application.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transportation:

 

Non-regulated by United States - Departmenrt of Transport (USDOT),

International Air Transport Association (IATA) or

International Maritime Organization (IMO)

 

VEHICLE TYPE

PIGMENTATION

THINNER

CLEANER

MIXING RATIO

INDUCTION TIME

POT LIFE

FLASH POINT

SOLIDS BY VOLUME

REC.FILM THICKNESS

SPREADING RATE / GAL

DRY TIME (Dust free)

DRY TIME (Service)

APPLICATION METHOD

STORAGE CONDITIONS

VOC

Epoxy / Aliphatic amines with inert plasticizer

Color / Inert / Fibrous reinforcement

Not normally required

MEK or lacquer thinner

2 : 1

Not required

Approx. 40 minutes / 77°F (25°C)

over 200°F (93.3°C)

100%

15-30mils / 107 – 53 sq.ft. / gal @ 20 mils

1604 mil/sq.ft/gal, 80 sq.ft /gal @ 20 mils

5 hours at 77°F (25°C)

14 hrs. lights, 72 hrs. heavy

Roller, brush, heated plural airless spray

Normal, Freezing OK

Essentially zero

Products Guideline

Corroserv (M) Sdn Bhd


A25 1st floor, Jalan IM 3/11,

Bandar Indera Mahkota,

25200 Kuantan, Pahang, Malaysia.

 

Tel        : +609-5735623

Fax      : +6095735562

email : admin@corroserv.com.my

Copyrights @ 2015 Corroserv (M) Sdn Bhd

 Downloads

 Technical Data Sheet

 Material Safety Data Sheet

 Application Procedures

 Case Histories
 Test Reports

 

 Training Videos

 Online Store

 Site Map